Napoleon Fireplaces GDI30 Manuel d'utilisateur télécharger pdf (Page 8)

W415-0806 / 06.28.09

2.0 INSTALLATION

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

Clean out ashes from the inside of the wood-burning appliance. Make sure that the chimney and wood-burning

appliance are in a clean and sound condition and constructed of non-combustible materials. If necessary have

any repair work done by a qualiﬁ ed person before installing the insert. Remove the existing appliance damper

or lock into an open position.

Using screws, attach the appliance warning tag

(W385-0199) to the inside of the ﬁ rebox of the ap-

pliance into which the insert is being installed.

The sheet-metal parts of the appliance, in which

the gas appliance insert is to be installed, must not

be cut.

If the wood-burning factory-built appliance has

no gas access hole(s) provided, an access hole of 1½ inch or less may be drilled through the lower sides or

bottom of the appliance in a proper workman like manner. This access hole must be plugged with non-combus-

tible insulation after the gas supply line has been installed.

Ensure that existing chimney cleanouts ﬁ t properly.

The refractory, glass doors, screen rails, screen mesh and log grates may be removed from the appliance

before installing the gas appliance insert.

Smoke shelves, shields and bafﬂ es may be removed if attached by mechanical fasteners.

The ventilation openings in the appliance may be obstructed by the backer plates, aluminium trim etc. but

these parts are not to be applied so as to have an airtight seal.

2.1 INSERT LEVELLING

Move the insert close to its ﬁ nal position inside the wood-burning appliance. This appliance is equipped with 4

levelling screws located in the four inside corners beneath the log support. Level using the levelling screws to

eliminate rocking or excessive noise when the fan is in operation. Once the appliance is level, move it partially

into place within the appliance to allow for all connections to be made. It is not practical to level the insert once

it has been installed. Determine the required depth prior to installing the appliance and adjust the four levelling

screws accordingly.

2.2 CHIMNEY CONNECTION

Chimney installation must conform to both national and local code requirements. The chimney must be lined

with one 2" or 3" diameter liner for intake and one 3" diameter liner for exhaust. The minimum and maximum

vent lengths are 10 and 35 feet respectively. Recommended Napoleon kits come in 3 lengths:

1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST & 2-3" TO 2" REDUCER:

GDI-2320KT VENT KIT 20FT

GDI-2325KT VENT KIT 25FT

GDI-2335KT VENT KIT 35FT

2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:

GDI-320KT VENT KIT 20FT

GDI-325KT VENT KIT 25 FT

GDI-335KT VENT KIT 35 FT

W385-0199_B

WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITH A GAS FIREPLACE

INSERT ONLY AND CANNOT BE USED FOR BURNING WOOD OR SOLID FUELS UNLESS ALL ORIGINAL

PARTS HAVE BEEN REPLACED AND THE FIREPLACE IS RE-APPROVED BY THE AUTHORITY HAVING

JURISDICTION.

ATTENTION: CE FOYER A ETE CONVERTI AFIN D’ETRE UTILISE SEULEMENT

COMME FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU

TOUT AUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALES AIENT

ETE REMPLACEES ET QUE LE FOYER SOIT APPROUVE DE NOUVEAU PAR LES AUTORITES

AYANT JURIDICTION.

ADVERTENCIA: ESTA CHIMENEA SE REMODELÓ PARA USARSE SOLO CON UNA

INSERCIÓN DE CHIMENEA A GAS Y NO PUEDE USARSE PARA QUEMAR MADERA NI COMBUSTIBLES

SÓLIDOS, A MENOS QUE SE HAYAN REEMPLAZADO TODAS LAS PIEZAS ORIGINALES, Y LA AUTORI-

DAD JURISDICCIONAL LA HAYA VUELTO A APROBAR.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 25 26

Commentaires sur ces manuels

Pas de commentaire

Napoleon Fireplaces GDI30 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Foyers Napoleon Fireplaces GDI30